1. Education
Send to a Friend via Email

Discuss in my forum

Calculating Concentration

Concentration Units & Dilutions

By

Do the units of calculation confuse you?

Do the units for solution concentration confuse you? Get definitions and examples for calculating percent composition by mass, mole fraction, molarity, molality, and normality.

Andy Sotiriou/Getty Images

Calculating concentration of a chemical solution is a basic skill all students of chemistry must develop early in their studies. What is concentration? Concentration refers to the amount of solute that is dissolved in a solvent. We normally think of a solute as a solid that is added to a solvent (e.g., adding table salt to water), but the solute could just as easily exist in another phase. For example, if we add a small amount of ethanol to water, then the ethanol is the solute and the water is the solvent. If we add a smaller amount of water to a larger amount of ethanol, then the water could be the solute!

Units of Concentration

Once you have identified the solute and solvent in a solution, you are ready to determine its concentration. Concentration may be expressed several different ways, using percent composition by mass, volume percent, mole fraction, molarity, molality, or normality.

  1. Percent Composition by Mass (%)

    This is the mass of the solute divided by the mass of the solution (mass of solute plus mass of solvent), multiplied by 100.

    Example:
    Determine the percent composition by mass of a 100 g salt solution which contains 20 g salt.

    Solution:
    20 g NaCl / 100 g solution x 100 = 20% NaCl solution

     

  2. Volume Percent (% v/v)

    Volume percent or volume/volume percent most often is used when preparing solutions of liquids. Volume percent is defined as:

    v/v % = [(volume of solute)/(volume of solution)] x 100%

    Note that volume percent is relative to volume of solution, not volume of solvent. For example, wine is about 12% v/v ethanol. This means there are 12 ml ethanol for every 100 ml of wine. It is important to realize liqud and gas volumes are not necessarily additive. If you mix 12 ml of ethanol and 100 ml of wine, you will get less than 112 ml of solution.

    As another example. 70% v/v rubbing alcohol may be prepared by taking 700 ml of isopropyl alcohol and adding sufficient water to obtain 1000 ml of solution (which will not be 300 ml).

     

  3. Mole Fraction (X)

    This is the number of moles of a compound divided by the total number of moles of all chemical species in the solution. Keep in mind, the sum of all mole fractions in a solution always equals 1.

    Example:
    What are the mole fractions of the components of the solution formed when 92 g glycerol is mixed with 90 g water? (molecular weight water = 18; molecular weight of glycerol = 92)

    Solution:
    90 g water = 90 g x 1 mol / 18 g = 5 mol water
    92 g glycerol = 92 g x 1 mol / 92 g = 1 mol glycerol
    total mol = 5 + 1 = 6 mol
    xwater = 5 mol / 6 mol = 0.833
    x glycerol = 1 mol / 6 mol = 0.167
    It's a good idea to check your math by making sure the mole fractions add up to 1:
    xwater + xglycerol = .833 + 0.167 = 1.000

     

  4. Molarity (M)

    Molarity is probably the most commonly used unit of concentration. It is the number of moles of solute per liter of solution (not necessarily the same as the volume of solvent!).

    Example:
    What is the molarity of a solution made when water is added to 11 g CaCl2 to make 100 mL of solution?

    Solution:
    11 g CaCl2 / (110 g CaCl2 / mol CaCl2) = 0.10 mol CaCl2
    100 mL x 1 L / 1000 mL = 0.10 L
    molarity = 0.10 mol / 0.10 L
    molarity = 1.0 M

     

  5. Molality (m)

    Molality is the number of moles of solute per kilogram of solvent. Because the density of water at 25°C is about 1 kilogram per liter, molality is approximately equal to molarity for dilute aqueous solutions at this temperature. This is a useful approximation, but remember that it is only an approximation and doesn't apply when the solution is at a different temperature, isn't dilute, or uses a solvent other than water.

    Example:
    What is the molality of a solution of 10 g NaOH in 500 g water?

    Solution:
    10 g NaOH / (40 g NaOH / 1 mol NaOH) = 0.25 mol NaOH
    500 g water x 1 kg / 1000 g = 0.50 kg water
    molality = 0.25 mol / 0.50 kg
    molality = 0.05 M / kg
    molality = 0.50 m

     

  6. Normality (N)

    Normality is equal to the gram equivalent weight of a solute per liter of solution. A gram equivalent weight or equivalent is a measure of the reactive capcity of a given molecule. Normality is the only concentration unit that is reaction dependent.

    Example:
    1 M sulfuric acid (H2SO4) is 2 N for acid-base reactions because each mole of sulfuric acid provides 2 moles of H+ ions. On the other hand, 1 M sulfuric acid is 1 N for sulfate precipitation, since 1 mole of sulfuric acid provides 1 mole of sulfate ions.

Dilutions

You dilute a solution whenever you add solvent to a solution. Adding solvent results in a solution of lower concentration. You can calculate the concentration of a solution following a dilution by applying this equation:

MiVi = MfVf

where M is molarity, V is volume, and the subscripts i and f refer to the initial and final values.

Example:
How many millilieters of 5.5 M NaOH are needed to prepare 300 mL of 1.2 M NaOH?

Solution:
5.5 M x V1 = 1.2 M x 0.3 L
V1 = 1.2 M x 0.3 L / 5.5 M
V1 = 0.065 L
V1 = 65 mL

So, to prepare the 1.2 M NaOH solution, you pour 65 mL of 5.5 M NaOH into your container and add water to get 300 mL final volume.

More Sample Concentration Calculation Example Problems

Worked Dilution Example
Three Worked Molarity Problems
Molarity Example Calculation
Percent Composition by Mass Example

Stay up to date on the latest chemistry news, learn chemistry, and get instructions for chemistry projects. Sign up for our free newsletter today!

©2014 About.com. All rights reserved.